Browsing by Subject "Equipment Failure Analysis"
Now showing 1 - 15 of 15
Results Per Page
Sort Options
Item Open Access A versatile diffractive maskless lithography for single-shot and serial microfabrication.(Opt Express, 2010-05-24) Jenness, Nathan J; Hill, Ryan T; Hucknall, Angus; Chilkoti, Ashutosh; Clark, Robert LWe demonstrate a diffractive maskless lithographic system that is capable of rapidly performing both serial and single-shot micropatterning. Utilizing the diffractive properties of phase holograms displayed on a spatial light modulator, arbitrary intensity distributions were produced to form two and three dimensional micropatterns/structures in a variety of substrates. A straightforward graphical user interface was implemented to allow users to load templates and change patterning modes within the span of a few minutes. A minimum resolution of approximately 700 nm is demonstrated for both patterning modes, which compares favorably to the 232 nm resolution limit predicted by the Rayleigh criterion. The presented method is rapid and adaptable, allowing for the parallel fabrication of microstructures in photoresist as well as the fabrication of protein microstructures that retain functional activity.Item Open Access Are component positioning and prosthesis size associated with hip resurfacing failure?(BMC Musculoskelet Disord, 2010-10-02) Marker, David R; Zywiel, Michael G; Johnson, Aaron J; Seyler, Thorsten M; Mont, Michael ABACKGROUND: Recent studies suggest that there is a learning curve for metal-on-metal hip resurfacing. The purpose of this study was to assess whether implant positioning changed with surgeon experience and whether positioning and component sizing were associated with implant longevity. METHODS: We evaluated the first 361 consecutive hip resurfacings performed by a single surgeon, which had a mean follow-up of 59 months (range, 28 to 87 months). Pre and post-operative radiographs were assessed to determine the inclination of the acetabular component, as well as the sagittal and coronal femoral stem-neck angles. Changes in the precision of component placement were determined by assessing changes in the standard deviation of each measurement using variance ratio and linear regression analysis. Additionally, the cup and stem-shaft angles as well as component sizes were compared between the 31 hips that failed over the follow-up period and the surviving components to assess for any differences that might have been associated with an increased risk for failure. RESULTS: Surgeon experience was correlated with improved precision of the antero-posterior and lateral positioning of the femoral component. However, femoral and acetabular radiographic implant positioning angles were not different between the surviving hips and failures. The failures had smaller mean femoral component diameters as compared to the non-failure group (44 versus 47 millimeters). CONCLUSIONS: These results suggest that there may be differences in implant positioning in early versus late learning curve procedures, but that in the absence of recognized risk factors such as intra-operative notching of the femoral neck and cup inclination in excess of 50 degrees, component positioning does not appear to be associated with failure. Nevertheless, surgeons should exercise caution in operating patients with small femoral necks, especially when they are early in the learning curve.Item Open Access Circuit topology and control principle for a first magnetic stimulator with fully controllable waveform.(Annual International Conference of the IEEE Engineering in Medicine and Biology Society. IEEE Engineering in Medicine and Biology Society. Annual International Conference, 2012-01) Goetz, SM; Pfaeffl, M; Huber, J; Singer, M; Marquardt, R; Weyh, TMagnetic stimulation pulse sources are very inflexible high-power devices. The incorporated circuit topology is usually limited to a single pulse type. However, experimental and theoretical work shows that more freedom in choosing or even designing waveforms could notably enhance existing methods. Beyond that, it even allows entering new fields of application. We propose a technology that can solve the problem. Even in very high frequency ranges, the circuitry is very flexible and is able generate almost every waveform with unrivaled accuracy. This technology can dynamically change between different pulse shapes without any reconfiguration, recharging or other changes; thus the waveform can be modified also during a high-frequency repetitive pulse train. In addition to the option of online design and generation of still unknown waveforms, it amalgamates all existing device types with their specific pulse shapes, which have been leading an independent existence in the past years. These advantages were achieved by giving up the common basis of all magnetic stimulation devices so far, i.e., the high-voltage oscillator. Distributed electronics handle the high power dividing the high voltage and the required switching rate into small portions.Item Open Access Clinical assessment and characterization of a dual tube kilovoltage X-ray localization system in the radiotherapy treatment room.(Journal of applied clinical medical physics, 2008-01-13) Lee, Sung-Woo; Jin, Jian-Yue; Guan, Huaiqun; Martin, Flavious; Kim, Jae Ho; Yin, Fang-FangINTRODUCTION:Although flat-panel based X-ray imaging has been well tested in diagnostic radiology, its use as an image-guided-radiotherapy (IGRT) system in a treatment room is new and requires systematic assessment. MATERIALS AND METHODS:BrainLab Novalis IGRT system was used for this study. It consists of two floor mounted kV X-ray tubes projecting obliquely into two flat-panel detectors mounted on the ceiling. The system automatically fuses the 2D localization images with 3D simulation CT image to provide positioning guidance. The following characteristics of the system were studied: (1) Coincidence of the isocenters between the IGRT and Linac; (2) Image quality; (3) Exposure; (4) Linearity, uniformity and repeatability. RESULTS:(1) Localization accuracy and coincidence of the isocenters between the IGRT and Linac was better than 1-mm. (2) The spatial resolution was quantified using the relative modulation-transfer-function with f50=0.7-0.9 lp/mm. The variation of contrast-noise-ratio with technical settings was measured. (3) The maximal exposure of an image was less than 95 mR. An empirical relation between the exposure and the X-ray technical setting was derived. (4) The linearity, uniformity and repeatability of the system generally meet the requirements. CONCLUSION:The system can be safely and reliably used as a target localization device.Item Open Access Coded aperture compressive temporal imaging.(Opt Express, 2013-05-06) Llull, Patrick; Liao, Xuejun; Yuan, Xin; Yang, Jianbo; Kittle, David; Carin, Lawrence; Sapiro, Guillermo; Brady, David JWe use mechanical translation of a coded aperture for code division multiple access compression of video. We discuss the compressed video's temporal resolution and present experimental results for reconstructions of > 10 frames of temporal data per coded snapshot.Item Open Access Delivery efficiency of an Elekta linac under gated operation.(Journal of applied clinical medical physics, 2014-09-08) Cui, Guoqiang; Housley, David J; Chen, Fan; Mehta, Vivek K; Shepard, David MIn this study, we have characterized the efficiency of an Elekta linac in the delivery of gated radiotherapy. We have explored techniques to reduce the beam-on delay and to improve the delivery efficiency, and have investigated the impact of frequent beam interruptions on the dosimetric accuracy of gated deliveries. A newly available gating interface was installed on an Elekta Synergy. Gating signals were generated using a surface mapping system in conjunction with a respiratory motion phantom. A series of gated deliveries were performed using volumetric modulated arc therapy (VMAT) treatment plans previously generated for lung cancer patients treated with stereotactic body radiotherapy. Baseline values were determined for the delivery times. The machine was then tuned in an effort to minimize beam-on delays and improve delivery efficiency. After that process was completed, the dosimetric accuracy of the gated deliveries was evaluated by comparing the measured and the planned coronal dose distributions using gamma index analyses. Comparison of the gated and the non-gated deliveries were also performed. The results demonstrated that, with the optimal machine settings, the average beam-on delay was reduced to less than 0.22 s. High dosimetric accuracy was demonstrated with gamma index passing rates no lower than 99.0% for all tests (3%/3 mm criteria). Consequently, Elekta linacs can provide a practical solution for gated VMAT treatments with high dosimetric accuracy and only a moderate increase in the overall delivery time.Item Open Access Design and in vivo evaluation of more efficient and selective deep brain stimulation electrodes.(Journal of neural engineering, 2015-08) Howell, Bryan; Huynh, Brian; Grill, Warren MObjective
Deep brain stimulation (DBS) is an effective treatment for movement disorders and a promising therapy for treating epilepsy and psychiatric disorders. Despite its clinical success, the efficiency and selectivity of DBS can be improved. Our objective was to design electrode geometries that increased the efficiency and selectivity of DBS.Approach
We coupled computational models of electrodes in brain tissue with cable models of axons of passage (AOPs), terminating axons (TAs), and local neurons (LNs); we used engineering optimization to design electrodes for stimulating these neural elements; and the model predictions were tested in vivo.Main results
Compared with the standard electrode used in the Medtronic Model 3387 and 3389 arrays, model-optimized electrodes consumed 45-84% less power. Similar gains in selectivity were evident with the optimized electrodes: 50% of parallel AOPs could be activated while reducing activation of perpendicular AOPs from 44 to 48% with the standard electrode to 0-14% with bipolar designs; 50% of perpendicular AOPs could be activated while reducing activation of parallel AOPs from 53 to 55% with the standard electrode to 1-5% with an array of cathodes; and, 50% of TAs could be activated while reducing activation of AOPs from 43 to 100% with the standard electrode to 2-15% with a distal anode. In vivo, both the geometry and polarity of the electrode had a profound impact on the efficiency and selectivity of stimulation.Significance
Model-based design is a powerful tool that can be used to improve the efficiency and selectivity of DBS electrodes.Item Open Access Flattening filter-free accelerators: a report from the AAPM Therapy Emerging Technology Assessment Work Group.(Journal of applied clinical medical physics, 2015-05-08) Xiao, Ying; Kry, Stephen F; Popple, Richard; Yorke, Ellen; Papanikolaou, Niko; Stathakis, Sotirios; Xia, Ping; Huq, Saiful; Bayouth, John; Galvin, James; Yin, Fang-FangThis report describes the current state of flattening filter-free (FFF) radiotherapy beams implemented on conventional linear accelerators, and is aimed primarily at practicing medical physicists. The Therapy Emerging Technology Assessment Work Group of the American Association of Physicists in Medicine (AAPM) formed a writing group to assess FFF technology. The published literature on FFF technology was reviewed, along with technical specifications provided by vendors. Based on this information, supplemented by the clinical experience of the group members, consensus guidelines and recommendations for implementation of FFF technology were developed. Areas in need of further investigation were identified. Removing the flattening filter increases beam intensity, especially near the central axis. Increased intensity reduces treatment time, especially for high-dose stereotactic radiotherapy/radiosurgery (SRT/SRS). Furthermore, removing the flattening filter reduces out-of-field dose and improves beam modeling accuracy. FFF beams are advantageous for small field (e.g., SRS) treatments and are appropriate for intensity-modulated radiotherapy (IMRT). For conventional 3D radiotherapy of large targets, FFF beams may be disadvantageous compared to flattened beams because of the heterogeneity of FFF beam across the target (unless modulation is employed). For any application, the nonflat beam characteristics and substantially higher dose rates require consideration during the commissioning and quality assurance processes relative to flattened beams, and the appropriate clinical use of the technology needs to be identified. Consideration also needs to be given to these unique characteristics when undertaking facility planning. Several areas still warrant further research and development. Recommendations pertinent to FFF technology, including acceptance testing, commissioning, quality assurance, radiation safety, and facility planning, are presented. Examples of clinical applications are provided. Several of the areas in which future research and development are needed are also indicated.Item Open Access High-fidelity, broadband stimulated-Brillouin-scattering-based slow light using fast noise modulation.(Opt Express, 2011-01-17) Zhu, Yunhui; Lee, Myungjun; Neifeld, Mark A; Gauthier, Daniel JWe demonstrate a 5-GHz-broadband tunable slow-light device based on stimulated Brillouin scattering in a standard highly-nonlinear optical fiber pumped by a noise-current-modulated laser beam. The noisemodulation waveform uses an optimized pseudo-random distribution of the laser drive voltage to obtain an optimal flat-topped gain profile, which minimizes the pulse distortion and maximizes pulse delay for a given pump power. In comparison with a previous slow-modulation method, eye-diagram and signal-to-noise ratio (SNR) analysis show that this broadband slow-light technique significantly increases the fidelity of a delayed data sequence, while maintaining the delay performance. A fractional delay of 0.81 with a SNR of 5.2 is achieved at the pump power of 350 mW using a 2-km-long highly nonlinear fiber with the fast noise-modulation method, demonstrating a 50% increase in eye-opening and a 36% increase in SNR in the comparison.Item Open Access In situ synthesis of DNA microarray on functionalized cyclic olefin copolymer substrate.(ACS Appl Mater Interfaces, 2010-02) Saaem, I; Ma, K; Marchi, A; LaBean, T; Tian, JThermoplastic materials such as cyclic-olefin copolymers (COC) provide a versatile and cost-effective alternative to the traditional glass or silicon substrate for rapid prototyping and industrial scale fabrication of microdevices. To extend the utility of COC as an effective microarray substrate, we developed a new method that enabled for the first time in situ synthesis of DNA oligonucleotide microarrays on the COC substrate. To achieve high-quality DNA synthesis, a SiO(2) thin film array was prepatterned on the inert and hydrophobic COC surface using RF sputtering technique. The subsequent in situ DNA synthesis was confined to the surface of the prepatterned hydrophilic SiO(2) thin film features by precision delivery of the phosphoramidite chemistry using an inkjet DNA synthesizer. The in situ SiO(2)-COC DNA microarray demonstrated superior quality and stability in hybridization assays and thermal cycling reactions. Furthermore, we demonstrate that pools of high-quality mixed-oligos could be cleaved off the SiO(2)-COC microarrays and used directly for construction of DNA origami nanostructures. It is believed that this method will not only enable synthesis of high-quality and low-cost COC DNA microarrays but also provide a basis for further development of integrated microfluidics microarrays for a broad range of bioanalytical and biofabrication applications.Item Open Access Instrument independent diffuse reflectance spectroscopy.(J Biomed Opt, 2011-01) Yu, Bing; Fu, Henry L; Ramanujam, NirmalaDiffuse reflectance spectroscopy with a fiber optic probe is a powerful tool for quantitative tissue characterization and disease diagnosis. Significant systematic errors can arise in the measured reflectance spectra and thus in the derived tissue physiological and morphological parameters due to real-time instrument fluctuations. We demonstrate a novel fiber optic probe with real-time, self-calibration capability that can be used for UV-visible diffuse reflectance spectroscopy in biological tissue in clinical settings. The probe is tested in a number of synthetic liquid phantoms over a wide range of tissue optical properties for significant variations in source intensity fluctuations caused by instrument warm up and day-to-day drift. While the accuracy for extraction of absorber concentrations is comparable to that achieved with the traditional calibration (with a reflectance standard), the accuracy for extraction of reduced scattering coefficients is significantly improved with the self-calibration probe compared to traditional calibration. This technology could be used to achieve instrument-independent diffuse reflectance spectroscopy in vivo and obviate the need for instrument warm up and post∕premeasurement calibration, thus saving up to an hour of precious clinical time.Item Open Access Intracellular Neural Recording with Pure Carbon Nanotube Probes.(PloS one, 2013-01) Yoon, Inho; Hamaguchi, Kosuke; Borzenets, Ivan V; Finkelstein, Gleb; Mooney, Richard; Donald, Bruce RThe computational complexity of the brain depends in part on a neuron's capacity to integrate electrochemical information from vast numbers of synaptic inputs. The measurements of synaptic activity that are crucial for mechanistic understanding of brain function are also challenging, because they require intracellular recording methods to detect and resolve millivolt- scale synaptic potentials. Although glass electrodes are widely used for intracellular recordings, novel electrodes with superior mechanical and electrical properties are desirable, because they could extend intracellular recording methods to challenging environments, including long term recordings in freely behaving animals. Carbon nanotubes (CNTs) can theoretically deliver this advance, but the difficulty of assembling CNTs has limited their application to a coating layer or assembly on a planar substrate, resulting in electrodes that are more suitable for in vivo extracellular recording or extracellular recording from isolated cells. Here we show that a novel, yet remarkably simple, millimeter-long electrode with a sub-micron tip, fabricated from self-entangled pure CNTs can be used to obtain intracellular and extracellular recordings from vertebrate neurons in vitro and in vivo. This fabrication technology provides a new method for assembling intracellular electrodes from CNTs, affording a promising opportunity to harness nanotechnology for neuroscience applications.Item Open Access Parallel on-axis holographic phase microscopy of biological cells and unicellular microorganism dynamics.(Appl Opt, 2010-05-20) Ehlers, MD; Newpher, Thomas Mark; Shaked, NT; Wax, AWe apply a wide-field quantitative phase microscopy technique based on parallel two-step phase-shifting on-axis interferometry to visualize live biological cells and microorganism dynamics. The parallel on-axis holographic approach is more efficient with camera spatial bandwidth consumption compared to previous off-axis approaches and thus can capture finer sample spatial details, given a limited spatial bandwidth of a specific digital camera. Additionally, due to the parallel acquisition mechanism, the approach is suitable for visualizing rapid dynamic processes, permitting an interferometric acquisition rate equal to the camera frame rate. The method is demonstrated experimentally through phase microscopy of neurons and unicellular microorganisms.Item Open Access Slow light with a swept-frequency source.(Opt Express, 2010-12-20) Zhang, Rui; Zhu, Yunhui; Wang, Jing; Gauthier, Daniel Jct: We introduce a new concept for stimulated-Brillouin-scattering-based slow light in optical fibers that is applicable for broadly-tunable frequency-swept sources. It allows slow light to be achieved, in principle, over the entire transparency window of the optical fiber. We demonstrate a slow light delay of 10 ns at 1.55 μm using a 10-m-long photonic crystal fiber with a source sweep rate of 400 MHz/μs and a pump power of 200 mW. We also show that there exists a maximal delay obtainable by this method, which is set by the SBS threshold, independent of sweep rate. For our fiber with optimum length, this maximum delay is ~38 ns, obtained for a pump power of 760 mW.Item Open Access Strategies to Aid Identification of Apheresis PowerFlow Ports: A Case Report.(Journal of emergency nursing, 2021-01) Gill, Janique C; Oakley, Darlene J; Onwuemene, Oluwatoyosi AIntroduction
The PowerFlow implantable apheresis intravenous port is a venous access device for therapeutic apheresis procedures. In this case review article, we identify key similarities and differences between apheresis PowerFlow ports and traditional ports. We also list strategies that emergency departments can implement to aid in correct port identification.Methods
Using a case review format, we describe the clinical presentation of a 33-year-old female with neuromyelitis optica who was evaluated in the emergency department for an acute exacerbation. She had a history of outpatient apheresis procedures that made use of bilateral PowerFlow ports. Mistaken for a conventional port, the right PowerFlow port was accessed with a Huber needle rather than the appropriate catheter-over-needle device. On infusion of intravenous fluids, the patient experienced pain and swelling. Ultimately, the port malfunctioned and was eventually replaced.Results
A subsequent root cause analysis identified opportunities for education and aids to improve port identification. To this end, strategies were implemented to appropriately identify the PowerFlow port using at least 2 of the following methods: (1) look in the patient's chart for record of an implantable apheresis intravenous port; (2) check the port identification card, bracelet, or keychain issued at insertion; (3) palpate the port to look for the rounded top and hollow concave entry point; and (4) use x-ray or fluoroscopy to identify radiopaque port markers.Conclusion
When a patient with a history of apheresis procedures presents with an implanted port, steps should be taken to ensure correct identification and access.